jaden

4 years ago

4 years ago

4 years ago

4 years ago

4 years ago

4 years ago

4 years ago

4 years ago

Hello, unfortunately I'm not aware of any field portable equipment with these capabilities but would also be interested in seeing this functionality being…

4 years ago

thanks for help, i will be greatfull of you would guide to one supplier of ultrasonic scanner to inspect railway grooved vignole Rail please find in…

4 years ago

It is his responsibility to make sure that standard quality welds are achieved, particularly by investigating condition of the electrodes, relevant…

4 years ago

Great to hear this Oleg. I am in the process of compiling use cases for AR, VR and MR as applied to NDT and Inspection. I will connect with you in a few weeks

4 years ago

There are two main disadvantages; 1) It requires much more flexibility in the excitation hardware, ideally the signal source and/or amplifier needs to be able…

4 years ago

You can find diferent NANDTB's in several countries, mainly in Europe COSAC en France, AEND in Spain, several institutes (Outside Agencies) in UK approved by…

4 years ago

firstly, the reason that ASTM EE3044 does not require the mode-converted time interval is because the shear mode is about 35dB lower than the P-mode so its…

4 years ago

One of the hardest things you will run into in evaluating hydraulic systems using Thermography is the identification of the various emissivity's found in the…

4 years ago

Rope Access / NDT combo will probably pay about the highest rates in the industry. There are a few Middle East trainers listed here…

4 years ago

In its most basic form, an RVI system is made up of a lens and an illuminating light source, both of which are connected to a light transmitting extension, at…

4 years ago

Optical film density in film radiography and grey value in CR and DR have some similarities but still they are not same. When we increase the radiation…

4 years ago

If you are doing this process, you should have a procedure to go along with it. What does your bonding verification method say about that?

4 years ago

The exhibitors will get the opportunity to showcase their products, technologies and services right away from home or office through a wide range of…

4 years ago

no doubt you will be inspecting the pressure vessel in accordance with the client-specified code or standard. You should be able to determine the calibration…

4 years ago

don't understand the question. Is it about differences between PAUT vs RT detection? if so then those are just two different methods to detect discontinuities…

4 years ago

MFL and LFET are methods used for scanning tank floors, piping, and tubing inspection. What application are you are interested in? I’ll focus on tank floor /…

4 years ago

Eddyfi offers LRUT training and CSWIP Certification in accordance with ISO9712. There are Level 1, 2 and 3 levels of Certification. If you would like further…

4 years ago

yes this is best for us.

4 years ago

It is an ultrasonic technique using a zero degree single crystal probe, to scan a surface. It is covered by ASME V

4 years ago

For acceptance criteria of PMI, it shall be demonstrated that materials contain the amount of alloying elements shown in the material specification. Alloys…

4 years ago

My experience has solely been with JME crawlers and they are very good. JME is a long-established company specializing in the field of pipeline crawlers…

4 years ago

You could be more specific such as: - Diameter of the piping, - Type of product in the line - Whether underground or above ground? - Whether testing can be…

4 years ago

Yes all of the probe elements are working properly. The problem is from 57 to 62 degrees where there is not even initial pulse.

4 years ago

In Quality Management System we have API SPEC Q2. Please give your advice as per your practice. Thank you in advance.

4 years ago

Why a foreigner couldn't work in any Nuclear Power Plant nor in any other plant? I thik that what above is regulated by the national law in force and the…

4 years ago

First off, I'd say YOU always control how much success you experience on your own path (as it appears you are already doing), regardless of others opinion. I…

4 years ago

This is not MPI and maybe a little too advanced, but I am sharing this with you in case it could be interesting considering it offers advantages…

4 years ago

Rosen Inspection GE Pipeline Services BJ Inspection NDT Services Weatherford T D Williamson 3P Inspection

4 years ago

The helium leak detection system can/should-be much, much more sensitive than the hydro/proof testing

4 years ago

Every details of Preheat/PWHT is given in WPS or you can find in design codes. When hydrogen related cracking may be there due to high thickness due to…

4 years ago